TI25002 Substation Engineering and Automation Syllabus:
TI25002 Substation Engineering and Automation Syllabus – Anna University UG Syllabus Regulation 2025
COURSE OBJECTIVES:
• To help engineering students gain a holistic understanding of the concepts behind substation engineering and design.
• The course aims to expose students to practical requirements, including an overview of civil and mechanical aspects.
• The course aims to enhance knowledge and provide practical guidelines for site selection, construction, protection, maintenance, and safety in substations.
• It also aims to provide knowledge about state-of-the-art technologies in substation automation systems.
UNIT I – SUBSTATION DESIGN DEVELOPMENT
Substation introduction and classifications – Different bus bar switching schemes for substations – Standards and practices – Factors influencing substation design: Altitude, ambient temperature, earthquake and seismic zones, pollution and corrosion – Testing of electrical equipment – Concept and development of single line diagram – Requirement of substation calculations.
UNIT II – SUBSTATION EQUIPMENT
Selection and sizing of main substation equipment: Transformer, isolator, circuit breaker, surge arrester, instrument transformers – Classification of equipment with practical overview and performance parameters – Classifications of MV switchgear and key design parameters – MV/LV switchgear construction and design of control scheme – Station auxiliary equipment: Diesel generator system – Basics of AC/DC auxiliary power system and sizing of auxiliary transformer – DC system components – Battery sizing and charger sizing – DG set classification and sizing – Introduction to gas insulated substation: Operating principle of GIS – Advantages over AIS – Construction of GIS.
UNIT III – PROTECTION AND SUBSTATION AUTOMATION
Power system protection – Overcurrent and earth fault protection and coordination – Distribution feeder protection – Transformer unit and main protection – Familiarization of numerical relays – Distance and differential protection for transmission lines – Substation automation: Evolution of substation automation – Communication system fundamentals – Protocol fundamentals and choosing the right protocol – Substation integration and automation functional architecture – Substation signal list: DI, DO, AI, AO – Bay control unit (BCU) – Remote terminal unit
(RTU).
UNIT IV – SUBSTATION DESIGN AND LAYOUT ENGINEERING
Layout aspects of outdoor air insulated substation and GIS – Statutory clearances – Equipment layout engineering aspects for outdoor substations and GIS with related calculations and guidelines – Cable routing layout – Erection key diagram (EKD) – Switchyard earthing design as per IEEE 80 – Importance and types of earthing – Earthing design – Types of earthing material – Direct stroke lightning protection for switchyard as per IS/IEC 62305 – LV cables: Power and control – MV cables – Methods for cable installation – Practical aspects of cable sizing – Cable accessories – Illumination system design.
UNIT V – INTERFACE ENGINEERING
Civil and structural engineering – Familiarization of site development plan – Equipment support structures – Foundation for equipment – Familiarization of control building and substation building – Infrastructure development – Mechanical systems: Fire detection and alarm system – Fire suppression system for transformers – Heating, ventilation and air-conditioning (HVAC) for substation.
TOTAL:45 PERIODS
SKILL DEVELOPMENT ACTIVITIES (GROUP SEMINAR/ MINI PROJECT/ASSIGNMENT/ CONTENT PREPARATION/ QUIZ/ SURPRISE TEST /SOLVING GATE QUESTIONS /ETC. 10
1. Battery sizing for a substation with a load cycle based on IEEE 1115 (Ni-Cd) – a case study. OR
2. DG and auxiliary transformer sizing for a substation auxiliary power supply – a case study.
3. Overcurrent relay coordination in a substation – a case study.
4. Earth mat sizing calculation for an outdoor substation based on IEEE 80 – a case study. OR
5. Direct stroke lightning protection calculation for an outdoor switchyard based on IEC 62305 – a case study.
REFERENCES:
1. McDonaldJohnD,“ElectricPowerSubstationsEngineering”,CRCPress,3rdEdition,2012
2. PartapSinghSatnam,P.V.Gupta,“Sub-stationDesignandEquipment”,Dhanpat Rai Publications, 1st Edition, 2013
3. SunilS.Rao,“Switchgear Protection and Power Systems (Theory, Practice & Solved Problems)”,Khanna Publications, 14th Edition, 2019 .
4. Electricalsubstationandengineering&practicebyS.Rao,3rdEdition,KhannaPublish ers 2015
6. Manualon Substation by Central Board of irrigation and Power(CBIP)Publication No 342., 2006.
7. SubstationautomationsystemDesignandimplementationbyEvelioPadillabyWiley Publications, 1st Edition, 2015 November.
